Custom Clothing Manufacturing for Streetwear Brands

A Streetwear Clothing Manufacturer Built for Small-Batch Drops

PRP Apparel manufactures streetwear at the fabric weights and finishes the category actually needs — 200–400 GSM heavyweight cotton, fleece, and French terry, garment-dyed and acid-wash styles, oversized cut-and-sew blocks, and decoration that holds up on heavy fabric — at a minimum of 50 pieces per style, per colour. Send a tech pack, a reference garment, or a rough sketch of the drop and we’ll reply with what it takes to get a sample started.

MOQ

50 Pieces Per Style

per colour — 3 colourways = 150 pieces

SAMPLE LEAD TIME

7–14 Days

per round, 1–3 rounds typical

BULK LEAD TIME

25–45 Days

from approved sample to shipped order

SAMPLE COST

$80–$250

per set, by construction complexity

Streetwear Needs Heavier Fabric and In-House Finishing, Not Just a Lower Minimum

Most factories that call themselves streetwear manufacturers are set up for lightweight basics — 140–180 GSM jersey, one wash cycle, minimal finishing — and stretch that line to cover a heavier order instead of running the equipment streetwear actually needs. PRP Apparel runs 200–400 GSM cotton, fleece, and French terry as standard input, with garment-dyed and acid-wash styles quoted as part of the same order rather than left for you to arrange with a separate wash house. For the deeper breakdown of what separates a real streetwear production line from a basics factory wearing a streetwear label, our guide to sourcing a streetwear manufacturer in China covers the infrastructure question in more depth — this page covers what we specifically run and what it costs to get a drop started.

Embroidery runs on our own 24-head line and all-over sublimation is printed in-house; screen print, DTG and heat transfer are available on the same order, so a drop that mixes a chest embroidery, a back-panel AOP graphic and heat-transfer labels is quoted and scheduled by one team instead of three. Cut-and-sew construction handles the oversized, dropped-shoulder, boxy silhouettes streetwear runs on — patterns are graded for that fit specifically, not a slim-fit block loosened at the seams. If you’re still working out what to check before committing to a factory for a drop-based line, our streetwear sourcing guide walks through the vetting questions in more detail.

Sample development runs 7–14 days per round, with most first styles settling within 1–3 rounds before we cut for bulk — cost is $80–$250 per sample set depending on construction. If a drop sells through, a reorder runs on the same 25–45 day bulk window and the same 50-piece-per-colour minimum as the first order.

Small-Batch Drops Get the Same Finishing Process as Bulk Runs

A 50-piece drop runs through the same cutting, finishing, and QC checkpoints as a 500-piece reorder — nothing gets shortcut because the run is small. The details below are what that looks like on the floor.

Laser-guided cutting table cutting heavyweight fabric for an oversized streetwear block

Our in-house 3-metre format laser cutter handles synthetic panels and cut-out details in one pass, with no panel piecing on oversized blocks. On synthetics the cut edge seals itself, so it does not fray.

Multi-head embroidery machine stitching a heavyweight herringbone panel for streetwear branding

Chest and sleeve embroidery runs on our own 24-head embroidery line, so an order that mixes an embroidered logo with a printed back panel doesn’t wait on a second vendor’s turnaround.

In-house heat-transfer press station used for heat-transfer labels and appliqué finishing on streetwear orders

Heat-transfer neck tags and pressed labels go through a heat-press station and are checked before a piece reaches packing.

Streetwear Production Specs

Every number below is our standard production term — the same terms whether the drop is 50 pieces or 500.

MOQ50 pieces per style, per colour — one style in one colour is a complete order; three colourways of the same style means 150 pieces
Sample lead time7–14 days from order confirmation
Sample cost$80–$250 per sample set, depending on complexity
Sample rounds1–3 rounds standard before bulk cutting
Bulk lead time25–45 days from approved sample to shipped order
Fabric weight range200–280 GSM for graphic tees and heavyweight blanks; 280–400 GSM for fleece hoodies and sweatshirts
Printing & finishingEmbroidery (in-house, 24 heads) and sublimation AOP (in-house); screen print, DTG and heat transfer available; garment-dyed and acid-wash styles
Decoration one-time feesDigitizing USD 40–100 per style (embroidery only); mould USD 40–100 per style (silicone patches only)
Laser cuttingIn-house, 3-metre format
ConstructionCut-and-sew, oversized and dropped-shoulder blocks, boxy silhouette grading
Order pathsOEM (your tech pack) · ODM (from your brief) · Private Label (rebrand a base style)
Fabric certificationOEKO-TEX Standard 100 available on request
Colorfastness testingISO 105-C06, ISO 105-X12, ISO 105-E04 on request

Which Decoration Holds Up on Heavyweight Streetwear

Most streetwear pieces carry a logo or graphic beyond print, and on 280–400 GSM fleece the choice of decoration decides how the piece looks after twenty washes. These are the four we see most on streetwear tech packs, compared on the points that actually change the order. For the full range of techniques, see our embellishment capabilities.

DecorationWorks onAvoidWash behaviourOne-time feeWhere it’s made
Flat embroideryFleece, French terry, heavy jersey, twillWaterproof-coated shells (needle holes break the coating), genuine leather, high-stretch knits without cut-away backing; lettering under about 5 mm fills inStitched in — lasts the life of the garmentDigitizing USD 40–100 per styleIn-house, 24 heads
Chenille patchHeavy fleece, twill, canvas, denim, melton woolLightweight knits, stretch fabrics, wovens under 120 gsm; letters under about 5 cm or strokes under 8 mm turn to mushSewn: life of the garment. Heat-press only: edges lift after 10–20 washesNonePartner facility
3D silicone patchFabrics that take 150–170°C for 10–15 seconds — cotton fleece and heavy jerseyThin nylon, ultralight polyester, wool, leather and PU, waterproof-coated fabric (use the sew-on version)50+ washes at 40°C; fails by edge lift, not by the silicone breaking downMould USD 40–100 per stylePartner facility
Laser-cut panels and cut-outsPolyester, nylon, poly mesh, neoprene, scuba, PU leather — the edge seals itself100% cotton fleece, linen, wool (edge scorches brown). PVC is never laser cut: it releases chlorine gasSealed synthetic edge does not fray and needs no hemmingNoneIn-house, 3-metre format

Embroidered and silicone patches cross over on cost: an embroidered patch has no mould fee, so it is cheaper on a 50-piece drop, while a silicone patch gets cheaper per piece as the run moves into the low hundreds.

Start With One Sample

Every drop is different, and most brands come to us with questions before they commit to a run. If you are not sure whether your design, your quantity or your timeline works with how we build, send it over — we will tell you what is possible.

The simplest way in is one sample. You get a physical garment in 7–14 days, in your fabric weight, with your decoration on it, before any bulk commitment. By the time bulk starts, the pattern, the fit and the finish are already approved.

Send a tech pack, a sketch, or a reference garment you like — all three work.

Where This Fits: One Drop or a Full Range

Streetwear is one of eight industries we build for, alongside fashion labels, startup brands, sportswear, and corporate uniform programs. If your line runs lighter and more fitted than a typical streetwear block — jersey tees, fitted silhouettes, less heavyweight fleece — see how we build for fashion brands placing full collections for the construction detail that fits that category better. If this is your first production order at any weight or fit, see how we work with startup and first-time brands. For the full fabric range including the heavier weights streetwear runs on, see the full fabric range.

Frequently Asked Questions

What's the minimum order for a streetwear drop?

50 pieces per style, per colour — a single design in one colour is a complete order, and three colourways of it is 150 pieces. Most drop-based brands start with one or two styles per season rather than a full range.

Can you run heavyweight fleece and garment-dyed or acid-wash styles?

Yes. 280–400 GSM fleece and French terry hoodies, including garment-dyed and acid-wash styles, are part of our standard range, and 200–280 GSM is the range for graphic tees and heavyweight blanks.

Do you handle embroidery and printing on the same order?

Yes. Embroidery runs on our own 24-head line and sublimation AOP is printed in-house; screen print, DTG and heat transfer are available on the same order, so one style can combine an embroidered logo with a printed graphic under a single quote.

Can you grade patterns for an oversized or dropped-shoulder fit?

Yes. Cut-and-sew patterns are graded for the block you send — oversized, boxy, dropped-shoulder — rather than a slim-fit pattern loosened at the seams, which changes the drape.

How long does a drop take from approved sample to delivery?

25–45 days for bulk production after the sample is approved, with sampling itself running 7–14 days per round and 1–3 rounds standard.

If a drop sells out, what does a reorder look like?

A reorder runs on the same 25–45 day bulk window and the same minimum of 50 pieces per style, per colour, as the first order. The approved sample and any digitizing file or patch mould from the first run are already on file.

Which decoration lasts longest on a heavyweight hoodie that gets machine-washed?

Embroidery and sewn-on chenille are stitched into the garment, so they last as long as the hoodie does. A correctly pressed 3D silicone patch survives 50+ washes at 40°C, and when it does fail it is the edge lifting, not the silicone breaking down. A chenille patch that is only heat-pressed starts lifting after 10–20 washes, which is why we sew chenille on anything that will be washed.

Are there one-time fees on top of the unit price for decoration?

Embroidery carries a one-time digitizing fee of USD 40–100 per style, and 3D silicone patches carry a one-time mould fee of USD 40–100 per style. On a 50-piece drop that works out to USD 0.80–2.00 per piece; on 300 pieces it is USD 0.13–0.33. Both are stated in the quote before sampling.

Ready to Start Your Streetwear Drop?

Send a tech pack, a reference garment, or a moodboard for the drop and we’ll reply with what it takes to get a sample started.